- Is soldering as good as welding?
- Can you use a paperclip as solder?
- Can you solder over old solder?
- Is there a substitute for solder?
- Why solder will not stick?
- Is solder as strong as welding?
- Why does my solder ball up?
- Will solder stick to any metal?
- How do you get solder to stick to steel?
- Can you solder without flux?
- Can you solder 2 pieces of metal together?
- Can I use Vaseline as flux?
- What metals does solder not stick to?
- What metals can you solder together?
Is soldering as good as welding?
Properly brazed joints can be stronger than the pieces being joined, but are not as strong as welded joints.
Brazing also has minimal effects on the two metal parts.
Soldering is a low-temperature analog to brazing.
The bond is not as strong as brazed joint or welded one..
Can you use a paperclip as solder?
This common mesh is galvanised steel i.e. steel which has been coated with zinc. Apparently paperclips are also made of galvanised steel as a rule, so there may be a connection here. … Other metals such as aluminium or regular steel can be soldered, but require special solder and flux and may need stronger equipment.
Can you solder over old solder?
Just heat the joint up with your torch, once the solder starts to melt use Channel locks to pull the fittings apart. Once the joint is apart, wipe as much old solder off as you can with a rag. Now you can start over. Clean, Flux, solder.
Is there a substitute for solder?
soldering two wires together doesn’t even require a soldering tool, but if you need to do some more intricate work, steel is the best choice for an impromptu tool. Steel wire, screwdrivers, nails, and Alan wrenches are all potential tools for your emergency soldering.
Why solder will not stick?
If you let the solder sit on the iron, the flux quickly boils off (the fumes are from flux, not the lead). And without flux, soldering becomes almost impossible. Flux removes oxidation from metals, and it’s crucial because solder won’t stick to oxidized metals, and metals oxidize very quickly at soldering temperatures.
Is solder as strong as welding?
Welding joints are the strongest, followed by soldered joints then brazed joints. Welding requires about 6,500 degrees Fahrenheit, while soldering requires about 840 degrees Fahrenheit. Workpieces and the metal base are heated and melted in welding. Soldering requires no heating of the workpieces.
Why does my solder ball up?
Solder balls are caused by gassing and spitting of the flux on the surface of the wave or by solder literally bouncing back from the solder wave. This is caused by excessive back flow in air or too high a drop in nitrogen environments.
Will solder stick to any metal?
It is important that all metal to be soldered is thoroughly clean. Solder simply will not adhere to dirty or oxidized metal surfaces. Clean any flat surfaces which are to be soldered with steel wool, a file, emery cloth, etc. It’s important to take time to clean the surface thoroughly.
How do you get solder to stick to steel?
To do this, heat up the soldering iron and touch the solder to the tip of the iron so that you cover the tip in a thin layer of solder. Wipe the excess off with a damp paper towel or sponge. Now, heat both the conductor you are trying to solder and the pad you are trying to solder to.
Can you solder without flux?
It’s ok, if you can do it, but it’s very difficult to solder without flux. The flux breaks down the oxide layers on the metal surfaces and allows the solder to “wet” them. If it doesn’t wet, it doesn’t make a connection. … It’s normally always necessary to use flux when you solder.
Can you solder 2 pieces of metal together?
Again, the concept is broadly similar to electrical soldering—you’re using a molten alloy to join two pieces of metal securely together—but the process is different: you use a gas torch and much higher temperatures than you’d use for electrical soldering or plumbing.
Can I use Vaseline as flux?
Can I use a Vaseline instead of flux? This question might just linger in your mind at the moment. The answer is yes. Using petroleum jelly as a soldering flux is an effective soldering flux alternative.
What metals does solder not stick to?
Basically all metals can be soldered, but we are looking for a low melting point soft solder and a flux. With the soft solders and a zinc chloride flux (most common), these metals will bond very easily: copper, tin, and brass. These metals will NOT bond: Iron, stainless steel, steel, and aluminum.
What metals can you solder together?
Suitable for joining copper, brass and many ferrous metals, including galvanized sheet metal, soldering is most often done with an electric soldering iron or soldering gun.